Terug naar blog
Koopgidsen 2026-11-17 Body Armor 4x4 7 weergaven

2010-2024 4Runner Pro Series II Rear Bumper: Buying Checklist

2010-2024 4Runner Pro Series II Rear Bumper: Buying Checklist

A practical buying checklist for the 2010-2024 4Runner Pro Series II rear bumper, covering fitment, trimming, sensor limits, swingout planning, and finish care.

Start with the 4Runner you actually drive

The Pro Series II rear bumper is listed for 2010-2024 Toyota 4Runner models. That is a broad range, but the catalog also flags two details that affect whether it suits your specific vehicle: the factory bumper requires trimming, and models with Blind Spot Monitoring (BSM) will need the system deactivated. Neither point is a dealbreaker, but both belong in your decision before you order.

The bumper is a bolt-on installation with no drilling required, though light to moderate mechanical skills are expected. The catalog lists an approximate install time of about one hour, which is useful as a planning baseline rather than a promise for every driveway.

Fit and installation facts that shape the purchase

Plan the swingout and accessory build now

The Pro Series II is modular, with options to add a single or dual tire/accessory swing. The catalog lists specific accessories: a driver-side swingout (TR-2965DS), a passenger-side swingout (TR-2965PS), and a tire carrier with license plate holder (TY-2966). If you plan to carry a larger spare or accessories, decide on single versus dual swing before you buy so you understand the full build.

The bumper also includes integrated shackle recovery mounts and light fitment for either two LED pods or flush mounts. These features are part of the bumper itself, but the catalog does not specify which LED pods or flush mounts fit, so confirm that separately if lighting is part of your plan.

Modularity and accessory support

Clearance, steps, and daily use

The bumper includes an integrated step for access to the rear or top of the SUV. The bolt-on quarter panel protection hoops also serve as steps and are rated to support up to 200 lbs. That rating is a useful limit to keep in mind for you and your passengers.

The catalog describes the design as following OE body lines, with an aggressive look. It does not provide specific departure angle measurements or clearance gains, so treat any clearance expectations as unconfirmed by the supplied information. If departure angle is a priority, compare the bumper’s physical dimensions to your current setup rather than relying on a claimed number.

Step and clearance-related facts

Finish care that protects the warranty

The bumper has a durable two-stage light texture black powder coat with a 3-year finish warranty and a limited lifetime warranty. To keep the finish intact, clean it only with mild soap on a damp sponge. Do not apply polish or wax that requires buffing for removal, and do not coat the product with any type of shine such as Tire Shine or glossy aerosol or gel. The catalog warns that these can damage the finish.

In areas with high concentrations of road salts and other corrosive agents, rust or damage to the finish may occur if the product is not properly maintained. The catalog recommends wiping down the product with a light coat of lubricant (such as WD40) periodically to maintain its luster. Surface rust, pitting, or discoloration from improper maintenance is not covered by the warranty, so following these care steps matters.

Finish and warranty details

  • 2010-2024 TOYOTA 4RUNNER PRO SERIES II REAR BUMPER: Durable two-stage light texture black powder coat; 3-year finish warranty and limited lifetime warranty. The warranty period is specific to the finish, so care instructions directly affect your coverage.
  • 2010-2024 TOYOTA 4RUNNER PRO SERIES II REAR BUMPER: Clean only with mild soap on a damp sponge; do not apply polish or wax that requires buffing, or any shine product like Tire Shine or glossy aerosol or gel. Using the wrong products can damage the finish and may void the finish warranty.
  • 2010-2024 TOYOTA 4RUNNER PRO SERIES II REAR BUMPER: BA recommends wiping down the product with a light coat of lubricant (i.e. WD40) periodically to maintain its luster. This is a simple maintenance step that helps preserve the appearance of the bumper.

What the catalog does not tell you

The supplied information does not include the bumper’s weight, the specific tools required beyond basic hardware, or detailed trimming instructions. It also does not list which LED pods or flush mounts are compatible. If any of these details are critical to your decision, confirm them with the manufacturer or installer before purchase.

The catalog price is USD 748.00, with a comparison price of USD 1100.00. That price difference may factor into your decision, but verify current pricing and availability at the time of order.

Gerelateerde artikelen

Customer Service
Home
Producten
Winkelwagen
Profiel