Quick answer
A 2.5-inch front strut spacer is a straightforward way to level a 2005-2023 6-lug Tacoma and clear up to 32-inch tires, and the Body Armor 4x4 spacer is built for both 2WD and 4WD trucks with a bolt-on install. Check your lug count and drivetrain first, then plan an alignment and a headlight adjustment after the lift.
What the 2.5-inch height actually changes
The spacer sits on top of the front strut assembly, so it raises the front ride height without changing spring rate or shock valving. That is why the catalog describes it as maintaining stock ride quality: the suspension still moves through its original travel, just from a higher starting point.
The practical result is a level stance and room for larger tires. It does not add wheel travel, so if you want more articulation for hard off-road use, a spacer is the wrong tool and a different suspension design is the right conversation.
Where a spacer lift stops making sense
A 2.5-inch front-only spacer is a leveling solution, not a full lift kit. If you regularly carry heavy loads or tow, the rear will still sit lower than the front, and you may want a matching rear change to keep the truck level when loaded.
Very tall spacers can also push the front geometry further than the stock components were designed for. At 2.5 inches you are in a common, well-understood range, but anything beyond that deserves a closer look at control arms, brake lines, and alignment range before you buy.
Tacoma strut spacer questions, answered
- Will this fit my Tacoma?
- It fits 2005-2023 Tacoma models with a 6-lug wheel pattern, in either 2WD or 4WD. Check your lug count before ordering, because 5-lug trucks are a different fitment and this spacer is not designed for them. Count the lugs on your truck, not the trim badge, before you buy.
- Does it work on both 2WD and 4WD?
- Yes. The catalog lists this spacer for both drivetrains, so you do not need a separate 2WD-specific part. The install steps are the same; the main difference is what you do afterward with alignment and driveline angles.
- What tire size can I run?
- The spacer is rated to accommodate up to 32-inch tires. That is a ceiling, not a guarantee: actual clearance depends on wheel width, offset, and tire brand, so test-fit before committing to a set. Measure clearance at full steering lock before buying tires.
- Will the ride get stiffer?
- No. Because the spacer sits above the strut and does not change the spring or shock, the catalog notes it maintains stock ride quality. What you will notice is a higher front end and a changed headlight aim. Plan a headlight adjustment after the lift.
- Do I need an alignment after installing it?
- Yes. Raising the front changes camber and toe, so book an alignment after the install. Driving on the old alignment will wear the front tires unevenly and can make the truck feel vague on the highway.
- Is installation really bolt-on?
- The catalog describes a bolt-on design with no modification required, using 1/4-inch steel construction and grade 10 hardware. You still need to support the truck safely, compress the strut assembly, and torque hardware to spec, so budget a few hours and a spring compressor. Have a spring compressor and torque wrench on hand before you start.
- Will it affect towing or hauling?
- The spacer only raises the front, so it does not increase payload or tow rating. With a heavy load in the bed, the rear will squat and the truck will sit nose-high, which is the point where a matching rear change makes sense.
Product facts
- 2005-2023 TOYOTA TACOMA (6 LUG) 2WD/4WD 2.5" STRUT SPACER: Fits 2005-2023 Toyota Tacoma 6-lug trucks in both 2WD and 4WD, with a 2.5-inch front lift for up to 32-inch tires. One part number covers a wide year range and both drivetrains, so you can confirm fitment without hunting for a separate 2WD version.

2005-2023 TOYOTA TACOMA (6 LUG) 2WD/4WD 2.5" STRUT SPACER - 2005-2023 TOYOTA TACOMA (6 LUG) 2WD/4WD 2.5" STRUT SPACER: Fabricated from 1/4-inch steel with grade 10 hardware and a bolt-on design. The steel construction and included hardware mean the install is a direct bolt-on rather than a fabrication project.


